PlayStation Vita Action Button Replacement

Main guide photo

Introduction

This guide takes you through the process of installing the action button on the PlayStation Vita.Image 1/2: Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.


Step 1  Case Separation

Image 1/2: Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.Image 2/2: Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.
Power off and remove the memory card.
Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.

Step 2

Image 1/3: Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover.


Using your fingernail or a spudger, pry open the accessory port cover on the top of the device.
Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover.

Step 3
Image 1/2:

Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port.

Step 4
Image 1/3: Continue working your way around the device gently prying it open.


Beginning at the sides of the device, use a plastic opening tool to separate the front and rear cases.
Continue working your way around the device gently prying it open.
There are still wires holding the front and rear cases together. You may damage the connections if you yank the cases completely apart.

Step 5
Image 1/2:


Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together.


Step 6
Image 1/1:
Using a spudger, free the touch screen controller flex cable by gently prying up the connection.

Step 7
Image 1/1:
Free the battery cable by gently prying up on the connection with a spudger.


Step 8
Image 1/1:
Separate the front and rear cases.

Step 9 Wireless Card
Image 1/3: Deroute the antenna cables so that they are out of the wireless card casing. Rest the wires out of the way.


Using the pointy end of the spudger, disconnect the three antenna cable connectors on top of the wireless card.
Deroute the antenna cables so that they are out of the wireless card casing. Rest the wires out of the way.



Step 10
Image 1/2: Peel up and remove the wireless card casing.


Hook the spudger beneath the tab on the wireless card casing and release the tab.
Peel up and remove the wireless card casing.

Step 11
Image 1/2: The wireless card will naturally pop out at an angle.


Remove the two 4.4mm Phillips #00 screws on the wireless card.
The wireless card will naturally pop out at an angle.
Pull out the wireless card.

Step 12 Right Shoulder Button
Image 1/3:


Pry up the right shoulder button casing with a spudger and set it aside.

Step 13
Image 1/1:
Remove the translucent, plastic right shoulder button cover.

Step 14
Image 1/3: Using tweezers, slide the flex cable out of the socket.



Release the right shoulder button flex cable socket by using a spudger to gently pry open the tab.
Using tweezers, slide the flex cable out of the socket.

Step 15
Image 1/2:


Using a spudger, gently peel up the right shoulder button from the light adhesive connecting it to casing.

Step 16 Right Button Board
Image 1/2: Remove the antenna cable.

Using the pointy end of a spudger, detach the antenna cable on the right button board.
Remove the antenna cable.

Step 17

Image 1/2: Gently pull the flex cable out of the socket. Rest the flex cable out of the way.

Using a spudger, pry up and release the ZIF socket on the right button board.
Gently pull the flex cable out of the socket. Rest the flex cable out of the way.

Step 18
Image 1/3: Using tweezers, gently pull the flex cable out of the socket. Rest the flex cable out of the way.



Release the tab on the small flex cable socket by prying up the tab with a spudger.
Using tweezers, gently pull the flex cable out of the socket. Rest the flex cable out of the way.

Step 19
Image 1/3: Remove the metal bracket, using a spudger as necessary to lift it out.Image 1/3: Remove the metal bracket, using a spudger as necessary to lift it out.



Remove the two 5.0mm Phillips #00 screws from the metal bracket securing the right button board to the motherboard.
Remove the metal bracket, using a spudger as necessary to lift it out.

Step 20
Image 2/3: Gently lift the right button board out.



Use a spudger to free the right button board by prying up from the bottom right corner of board.
Gently lift the right button board out.

Step 21 Action Button
Image 1/3:



Using tweezers, gently peel the action button off the back casing assembly.

Author
Brittany McCrigler
Member since: 03/05/2012
72,171 Reputation
403 Guides authored

 


0 comments

Leave a comment

Please note, comments must be approved before they are published