Step 1 Battery
Lift the battery cover off the back of the DSi XL.
Remove the two Phillips screws securing the battery cover to the back of the handheld console.
Lift the battery cover off the back of the DSi XL.
Step 2
Lift the battery from the DSi XL.
Step 3 Lower Case
Remove the four rubber screw covers on the lower case by prying them up with a push pin.
Step 4
Four silver 5.3 mm screws
Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:
Four silver 5.3 mm screws
Two black 5.3 mm screws
One black 2.5 mm screw
Step 5
Insert a spudger between the upper and lower case at the bottom left corner of the DSi.
Turn the DSi XL over, and open the display.
Insert a spudger between the upper and lower case at the bottom left corner of the DSi.
Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.
Step 6
Lift the lower case from the front edge.
Close the display and turn the DSi XL over.
Lift the lower case from the front edge.
Rotate the lower case away from the DSi.
The lower case cannot be completely removed yet, since it is still connected to the motherboard.
Step 7
Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.
Using a spudger, pry the SD card/right shoulder button connector off its socket.
Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.
Step 8 Wi-Fi Board
Do not attempt to completely remove the Wi-Fi board yet. It is attached to the motherboard by an antenna cable.
Lift the Wi-Fi board up off its socket on the motherboard.
Do not attempt to completely remove the Wi-Fi board yet. It is attached to the motherboard by an antenna cable.
Step 9
Use a spudger to pry the Wi-Fi cable off its socket on the underside of the Wi-Fi board.
Step 10 Motherboard
Pry from underneath the cable.
Use a spudger to pry the microphone cable off the motherboard.
Pry from underneath the cable.
Step 11
Use the pointed end of a spudger to pull the camera ribbon from the ZIF connector.
Using the flat end of a spudger, flip up the retaining flap on the camera ribbon ZIF connector.
Use the pointed end of a spudger to pull the camera ribbon from the ZIF connector.
Step 12
With the pointed end of the spudger, pull the touchscreen cable from its connector on the motherboard.
Using the flat end of a spudger, flip up the retaining flap on the touchscreen cable ZIF connector.
With the pointed end of the spudger, pull the touchscreen cable from its connector on the motherboard.
Step 13
With the pointed end of the spudger, pull the backlight cable from its connector on the motherboard.
Using the flat end of a spudger, flip up the retaining flap on the backlight cable ZIF connector.
With the pointed end of the spudger, pull the backlight cable from its connector on the motherboard.
Step 14
With the pointed end of the spudger, pull the lower display data cable from its connector on the motherboard.
Using the flat end of a spudger, flip up the retaining flap on the lower display data cable ZIF connector.
With the pointed end of the spudger, pull the lower display data cable from its connector on the motherboard.
Step 15
With the pointed end of the spudger, pull the D-Pad/power button cable from its connector on the motherboard.
Using the flat end of a spudger, flip up the retaining flap on the ZIF connector for the D-Pad/power button cable.
With the pointed end of the spudger, pull the D-Pad/power button cable from its connector on the motherboard.
Step 16
Using the flat end of the spudger, pry the battery cable up off its socket on the motherboard.
Step 17
A single 2.5 mm silver Phillips screw
Remove the screws securing the motherboard to the upper case:
A single 2.5 mm silver Phillips screw
Four 3.7 mm black Phillips screws
Step 18
Deroute the microphone and antenna cables through the slot in the motherboard.
Step 19
The motherboard cannot be completely removed yet. It is still attached by the upper LCD's display data ribbon cable.
Rotate the motherboard off the lower case.
The motherboard cannot be completely removed yet. It is still attached by the upper LCD's display data ribbon cable.
Step 20
With the pointed end of the spudger, pull the upper display data cable from its connector on the underside of the motherboard.
Using the flat end of a spudger, flip up the retaining flap on the upper display data cable ZIF connector.
With the pointed end of the spudger, pull the upper display data cable from its connector on the underside of the motherboard.
The motherboard is now free from the upper case.
Step 21 Buttons
Lift the rubber pad off the back of the buttons.
Step 22
Remove all four buttons from the DSi XL.
Open the display slightly, and push each button away from the upper case.
Remove all four buttons from the DSi XL.
Author
Brett Hartt
Member since: 04/12/2010
95,948 Reputation
190 Guides authored
