DualShock 4 Right Analog Stick Replacement

Main guide photo

Introduction

Here is a DualShock 4 controller that had a drift to both analog joysticks. Fairly straight forward replacement of the joysticks resolved the issue.

 

Step 1 Controller

Image 1/1: Do not forcefully loosen the screws, as it will amount to permanent damage of the threads, making removal impossible.
Using the Phillips #00 Screwdriver, remove the four 6.0 mm screws securing the rear cover to the controller.
Do not forcefully loosen the screws, as it will amount to permanent damage of the threads, making removal impossible.

 

Step 2
Image 1/3: Pinch the left shoulder of the controller to introduce an opening.

Beginning with the left shoulder:
Pinch the left shoulder of the controller to introduce an opening.
Wedge a plastic opening tool into the opening and slide it up towards the joystick.
Pull down on the plier to crack open the casing.
Repeat these steps for the right shoulder.

 

Step 3


Image 1/3: '''Share''' button
Wedge a plastic opening tool into the case-splittings and pull down to crack open the casing near the following buttons:
Share button
Options button
Split the plastic covers of the controller apart, taking note that they will still be attached by circuit board ribbons.
Three small pieces are often released from the framework. To prevent loss, maintain a controlled work field.
2 Trigger Springs
1 Grey Reset Button Extension



Step 4 Battery


Image 1/3: After the two halves are separated, place the top of the controller off to the side.

Detach the motherboard ribbon connecting the two sides of the controller by using your fingers.
After the two halves are separated, place the top of the controller off to the side.

 

Step 5


Image 1/3: After removal of the plug from the motherboard, the battery can be lifted off of the controller.

Using the blunt forceps, remove the battery plug by gently rocking the forceps side-by-side to loosen the plug.
After removal of the plug from the motherboard, the battery can be lifted off of the controller.
Hasty removal of the battery plug could warp the plastic grips of the plug.

 

Step 6 Disassembling DualShock 4 Motherboard Assembly


Image 1/1: Do not forcefully loosen the screw, as it may amount to permanent damage of the threads, making removal impossible.

Remove the single 6.0 mm Phillips screw found below the battery retainer with the Phillips #00 Screwdriver.
Do not forcefully loosen the screw, as it may amount to permanent damage of the threads, making removal impossible.

 

Step 7


Image 1/2:

Gently detach the touchpad ribbon connected to the motherboard using the blunt forceps. The touchpad ribbon is connected to the motherboard by a connector that flips to tighten and loosen. During reassembly, to reattach the ribbon, the plastic tray will need to be gently removed from the motherboard and the flip-lock flipped up.

 

Step 8

Image 1/2: Vibration motors are loosely attached to the motherboard assembly. Provide support at the two ends to ease the separation.

Carefully dislodge the motherboard assembly from the front cover.
Vibration motors are loosely attached to the motherboard assembly. Provide support at the two ends to ease the separation.
When removing the motherboard assembly, try not to tilt the front cover upside down as the buttons and their covers may fall out.

 

Step 9 Disassembly Complete

Image 1/3: Motherboard Assembly

Successful disassembly of the controller will result in the following three parts, respectively:
Motherboard Assembly
Front Cover
Rear Cover


Step 10 Right Analog Stick

Image 1/3: Use a desoldering wick and flux to melt and remove the solder

These are the solder connections that will need to be desoldered. Since the board is upside down, left will become right.
Use a desoldering wick and flux to melt and remove the solder
This may take a bit of practice since all the solder will have to be removed. It does help to pull a bit on the joystick while melting the solder and using the wick.

 

Step 11


Image 1/3: Check that all the holes are cleared of old solder. Hypodermic needles as well as very small drill bits can be used to clear the holes.

Once all the contacts are desoldered, the old joystick can be removed.
Check that all the holes are cleared of old solder. Hypodermic needles as well as very small drill bits can be used to clear the holes.
Insert the new joystick into the circuit board. Make sure it is properly seated and that all the contacts line up with the holes in the circuit board.

 

Step 12


Double check to make sure the joystick is seated properly.
Solder all the contacts to the board.
Here is the board after the repair. All that is left is to clean off the old flux with some isopropyl alcohol.

Author
oldturkey03
Member since: 09/29/2010
416,195 Reputation
96 Guides authored

 


0 comments

Leave a comment

Please note, comments must be approved before they are published